Basic Electronics

What is Inductor? Its types, Inductors in parallel, Inductors in Series

Inductor Introduction:

Inductor

An inductor is passive component which consist of two terminals it is also called a coilchokes, or reactor, when electric current flow through it, it store energy in form of magnetic field. Magnetic field will be generated when current flows in the coil. Inductors are mostly used for the opposition of current.

Electromotive force is produced in inductor when the current changes in the inductor that described by Faraday’s law of induction that whenever the flux is changing in the circuit it will induced voltage in the circuit. According to Lenz’s law the induced EMF will opposes the change in current that created it.

The inductance of inductor can is given by the equation:

Inductor

From the above equation we can see that the inductance is the ratio between voltage and changing current.

Inductor Unit:

The unit of inductance is henry (H) due to American Scientist Joseph Henry.

In the measurement of magnetic circuits, this equal to weber/ampere in which weber is the unit of changing magnetic flux and ampere is the unit of current.

Inductor Construction:

An inductor is a coil that is insulated copper wire, wrapped around a core of ferromagnetic material.

Many inductors are made up of iron core in which ferrite are present inside the core.


Inductor Applications:

Tuning circuits

The tuning circuits can select the desired frequency with the help of an inductor. Various electronic devices use inductors along with the capacitor to modify the frequency.

 Sensors

The inductive proximity sensors are very useful in operation and are a contactless sensor. In sensors magnetic field is produced which works on Inductance principle. The traffic lights used proximity sensors mechanism to detect the traffic density.

Store energy

Inductors can store energy for a small interval of time because when the power supply is detached the magnetic field will be gone. Computers circuits use inductors where power supplies can be switched.

Induction motors

In the induction motors, the magnetic field is produced due to alternating current which will be used to rotate the shaft in the motor. The speed of the motor can be control according to the frequency. With the help of inductors, we can control the speed of the induction motor.

Inductors separate different frequencies work as an electronic filter. It makes tuned circuits when combined with capacitors used in TV and Radio receivers.

Inductors are mostly used in signal processing and analog circuits. In power supply with a filter capacitor, it removes ripples.

The switch-mode power supply uses Inductors to store energy and to produce DC current. Energy is supplied to the circuit by inductor during its off switching periods to keep the current flow.

Symbols for Inductors

Inductor



TYPES OF INDUCTOR

Air cored inductor:

This type of inductor achieved specified inductance without use of ferromagnetic.

Iron losses which mostly affect ferromagnetic cores are not present in air cored inductor.

Due to which frequency is increased and we obtain better Q-factor, greater power handling and less distortion.

Air cored inductors are designed for higher frequencies such as 1 GHz. Most ferromagnetic cores lossy above 100 MHz

Inductor

Iron cored inductor:

The iron core inductors are designed for low value of inductance. In the iron core inductor, inductance can be increased by using iron core. The iron core inductor have iron core placed inside the coil it is fixed value inductor.

Iron cores are normally used when high inductance and high power is required. Iron laminate are used for some audio coils or chokes.

Inductor

Ferrite cored inductor:

Ferrite is one of the mostly used cores for a various types of inductor. Ferrite is a metal oxide ceramic they are also known as ferromagnetic materials  based around a mixture of Ferric Oxide Fe2O3 and either manganese-zinc or nickel-zinc oxides which are extruded or pressed into the required shape.

Inductor

 


Soft ferrites: 

Soft ferrites are not permanent magnets.  Soft ferrites are ferrite materials reverse the polarity of their magnetization without a significant amount of energy being needed to reverse the magnetic polarity. In the Soft ferrites inductors a ferrite core placed inside the coil are known as a ferrite core inductor. There is only a relatively small loss of energy in soft ferrites.

Inductor

Hard ferrites:  

 Hard ferrites are made up of iron, strontium oxide or barium. They are also called permanent magnets. They hold the polarity of their magnetization when the magnetizing field has been removed, i.e. they have a high remanance level they are mostly used as household magnets.

Inductor

Iron power inductor:  

 

Iron oxide is another type of inductor which is widely used. it has high permeability which enables it to provide higher inductance.

Inductor


Inductors may also be categorized in terms of their mechanical construction. There are a number of different standard types by which inductors may be categorized:

Bobbin based inductor:  

This type of inductor is on a cylindrical bobbin. They may be used for mounting printed circuit board. Some older versions of these inductors may even be in a similar format to normal leaded resistors.

Inductor

Toroidal inductor:  

This is circular form inductor is wound on a toroid. Ferrite is often used as the former as this increases the permeability of the core.

 In this type of inductor flux leakage is very low because magnetic flux travel in circular form.

The disadvantage is that it require special winding machine to perform the manufacture as the wire has to be passed thought the toroid for each turn required.

Inductor

Multilayer ceramic inductor:  

This type of inductor is mostly used for surface mount technology. Magnetic ceramic material or ferrite is used for its construction.

It is made up of ceramic in which coil is placed like chip capacitors external circuit is presented on its end caps.

Inductor


HOW INDUCTOR WORKS:

The inductor stores the electrical energy in the form of the magnetic field. It is constructed by wounding the wire on the core. The cores are made of iron, ceramic material or by the air. The core may be E- shaped or toroidal.

The current flow in the coil it produce the magnetic field around the coil. The intensity of the magnetic field increases if the core is placed between the coil. The core provides the low reluctance path to the magnetic flux.

Inductors and DC

A Magnetic field is created around the inductor when DC signal passing through it. This magnetic field can be used for several functions. Automotive relay mostly used coil inside it.

Magnetic field is generated when the coil is energized by DC signal changes the state of the relay from an Open to a Closed state. Most electromagnetic relays work on this principal.

Inductors and AC

Magnetic field is produced in the circuit when ac current flow in the circuit. However, as AC signals the magnetic field is changing when the signal are changing from positive (+) to negative (-). Inductance is created when the magnetic flux is changing in a coil. The gauge of wire and number of windings in the inductor decide the inductance.

Four physical factors that determine inductor inductance:

Inductor depends upon on the following factors:

Inductor

1) Number of turns:  From the above formula we see that inductance is directly proportion to square of number of turns greater the number of turns greater will be the inductance.

2) Permeability of the core – Permeability is the resistance against the magnetic field. When we increase the permeability of material inductance will be increased. Iron cores have provided higher permeability.

3) Cross-sectional area – Area is also directly related with the inductance of a coil. When the area increases the inductance will be increases.

4) Length – The inductance of a coil decreases as its length increases because there is inverse relation between length and inductance.



Difference between an Inductor and Capacitor

First things to note that both inductor and capacitor store energy when a voltage potential is applied across it, but Inductor stores energy in form of a Magnetic felid and Capacitor stores electrical charges in form of an Electric Field.

Now to understand we know that Capacitor tries to level the voltage in a circuit, capacitor charge or discharge to level up the voltage. When the potential difference is applied around the terminal of capacitor an electric field is formed and electric charges are stored.

The capacitor’s value can be determined, the distance between the two terminals, by the size of the terminals, and the kind of material used.

Inductor is work as short circuit for direct current and grants an opposing force to alternating current that depends on the current’s frequency. The opposition to a flow of the current of an inductor is associated with the frequency of the flowing current through it.

Inductors in Series and Parallel

We can connect inductor in series or parallel.

Inductors in Series:

When we connect the inductor in series we can find the equivalent inductance by simply adding the inductors

Inductor

L = L1  + L2 +L3 … + Ln

Where L is the total inductance and L1, L2,L3…Ln are the individual inductances.

Suppose we  have three inductors  measuring 10uH,  20uH and the other 30uH, then by putting them in series you obtain a total inductance of 60uH.


Inductors in Parallel:

Inductor

Inductors in parallel behave the same way as resistors in parallel, the inductance is given by:

1/L = 1/L1 + 1/L2 +1/L3 … + 1/Ln

Where L is the total inductance and L1, L2, L3…Ln are the individual inductances.

In this way if we have connect three inductors 10uH, 20uH and 3 0uH inductors in parallel then the inductance will be:

By cross multiplication we get

                                                                                60=11XLeq

Dividing both sides by 11

Inductor


Useful Inductor Formulas

1. ENERGY STORED BY INDUCTORS:

Inductors can store energy much like capacitors until the power is supply to it, but the energy is gone at the moment when we disconnect the power and the magnetic field collapses. In other words, an unpowered inductor cannot sustain its magnetic field without power supply

Inductor

Where E represents energy in Joules, L is the inductance and I is the current in amperes.

This relation states that energy is directly proportional to the inductance and the current greater the value of the current and inductance greater will be the energy.

Now consider example if we have an inductor of 10uH with a 2A current flowing through it, then the energy stored will be:

Inductor

2. RATE OF CURRENT RISE

The voltage can be calculated by using the formula:

Inductor

This equation states that the current rises in linear form when a constant voltage is applied across the inductor.

3. IMPEDANCE

Inductors have impedance that is related to the frequency by the formula:

Inductor

Where the inductive impedance, f is the frequency in Hertz and L is the inductance in Henrys.


Inductor Behavior in Circuits

Inductors are useless in DC circuits, since there is a constant current flowing in dc circuits and the inductor acts like a bit of wire. Inductors are mostly used in AC circuits they have an impedance, which makes them useful to limit current in an AC circuit, such as fluorescent lamp ballasts.

They can also be used to filter signals.

Inductor

In the above circuit we have resistor connected with inductor which is also known as choke filter; the inductor allows all DC current to flow through it to ground behaving like wire, preventing all the low frequencies from reaching the output the inductor will offer high resistance to ac and no resistance to dc. At higher frequencies, the impedance of the inductor increases steadily, so the signal can pass through to the output, hence it is called a high pass filter.

Mathematical Expression can be calculated by using the following formulas:

Let the voltage across load resistor RL  be VL . Thus, the value of  VL is given by the below equation.

Inductor

Inductor

  RL will cancel each other

Inductor

Where VDC the DC output voltage is output of full wave rectifier, and RC  is the resistance of inductor coil.


Inductor in a Circuit:

Now we will discuss what inductor do in the circuit it resists the change in current in the circuit.

In the circuit below, we have a resistor and LED in series with an inductor. And switch to turn the power on and off.

Inductor

Without the inductor, this would just be a normal LED circuit and the LED would turn on right away when we supply the power.  Changes in current will be resisted by the inductor. When the switch is off, there is no current flowing. When switch on, current starts flowing through the circuit. So instead of the current going from zero to maximum right away, it will gradually increase up to its maximum current. The resistor and LED will set the maximum current for the circuit.

The light intensity of the led will be decided by the current and will make the led fade in.

 When the switch is closed the current will rises in exponential it will not rise immediately. This is due to the fact change in current flow through the inductor causes BACK EMF in the circuit. This back EMF has an amplitude that is proportional to the RATE OF CHANGE of current (the faster the rate of change, the greater the back EMF) and polarity which opposes the change in current in the inductor that caused it initially. The back EMF is produced when the current in the inductor is changing which will the change in the magnetic field, which will induce back emf. This process is called SELF INDUCTION.

Engr Fahad

My name is Shahzada Fahad and I am an Electrical Engineer. I have been doing Job in UAE as a site engineer in an Electrical Construction Company. Currently, I am running my own YouTube channel "Electronic Clinic", and managing this Website. My Hobbies are * Watching Movies * Music * Martial Arts * Photography * Travelling * Make Sketches and so on...

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button